Asus X38 Series BIOS Settings from OPB
CPU Feature:
Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Control [Manual]
Ratio CMOS Setting: [8]
FSB Frequency [450]
FSB Strap to North Bridge [Auto]
PCIE Frequency [110 for 3D; 100 for normal]
DRAM Settings: DDR2(MF) DDR3(ME & P5E3)
DRAM Frequency [對應frequency及strap]
DRAM Command Rate [Auto]
DRAM Timing Control [Manual]
CAS# Latency [5]
RAS# to CAS Delay [5]
RAS# Precharge [5]
RAS# Active Time [12]
RAS# To Ras# Delay [3]
Row Refresh Cycle Time [42]
Write Recovery Time [6]
Read To Precharge Time [3]
Read To Write Delay(S/D) [8]
Write To Read Delay(S) [3]
Write To Read Delay(D) [5]
Read To Read Delay(S) [4]
Read To Read Delay(D) [6]
Write To Write Delay(S) [4]
Write To Write Delay(D) [6]
DRAM Static Read Control [Disabled]
Ai Clock Twister [Strong]
Transaction Booster [Enabled]
Boost Level [0]
Voltage Settings:
CPU Voltage [1.3v~1.4v]
CPU PLL Voltage [Auto]
North Bridge Voltage [1.61v~1.7v]
DRAM Voltage [2.16v~2.35v]
FSB Termination Voltage [1.5v]
South Bridge Voltage [Auto]
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.67x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
感謝狂少大大又提供X38主機板超頻教學了;tongue;
連看了幾天狂大提供的教學,總算初步學會X38的基本超頻了^^
Asus Maximus Formula Bios簡介與OC 設置分享
Maximus formula真的那麼難攪定嗎?10張圖讓你了然於胸
上面兩篇文章已經是精華了 ,今天又提供新的教學,真是太棒了;nq;
看了狂大那麼多教學,也該做點回饋了;rr;
E2140 1.6G OC 3.6G Mhz
1GB DDR2 800Mhz OC 1200Mhz
我的主機板為Maximus formula BIOS 0907
我的主機板BIOS設置,因CPU跟狂大的不同,所以設置上有些許改變
後方紅字部份為我的BIOS設定
如下:
Asus X38 Series BIOS Settings from OPB
CPU Feature:
Ai Overclock Tuner [Manual]
設置一樣
OC From CPU Level Up [Auto]
E2140沒有這個選項一.一
CPU Ratio Control [Manual]
設置一樣
Ratio CMOS Setting: [8]
設置AUTO
FSB Frequency [450]
設置一樣
FSB Strap to North Bridge [Auto]
設置一樣
PCIE Frequency [110 for 3D; 100 for normal]
設置100
DRAM Settings: DDR2(MF) DDR3(ME & P5E3)
DRAM Frequency [對應frequency及strap]
系統顯示DDR2 1200
DRAM Command Rate [AUTO]
設置2T
DRAM Timing Control [Manual]
設置一樣
CAS# Latency [5]
設置一樣
RAS# to CAS Delay [5]
設置一樣
RAS# Precharge [5]
設置一樣
RAS# Active Time [12]
設置15
RAS# To Ras# Delay [3]
設置AUTO
Row Refresh Cycle Time [42]
設置AUTO
Write Recovery Time [6]
設置AUTO
Read To Precharge Time [3]
設置AUTO
Read To Write Delay(S/D) [8]
設置AUTO
Write To Read Delay(S) [3]
設置AUTO
Write To Read Delay(D) [5]
設置AUTO
Read To Read Delay(S) [4]
設置AUTO
Read To Read Delay(D) [6]
設置AUTO
Write To Write Delay(S) [4]
設置AUTO
Write To Write Delay(D) [6]
設置AUTO
DRAM Static Read Control [Disabled]
設置AUTO [不懂該項目,目前設置系統預設值AUTO]
Ai Clock Twister [Strong]
設置一樣
Transaction Booster [Enabled]
設置一樣
Boost Level [0]
設置一樣
Voltage Settings:
CPU Voltage [1.3v~1.4v]
設置1.56250v
CPU PLL Voltage [Auto]
設置一樣
North Bridge Voltage [1.61v~1.7v]
設置1.61
DRAM Voltage [2.16v~2.35v]
設置AUTO
FSB Termination Voltage [1.5v]
設置AUTO
South Bridge Voltage [Auto]
設置AUTO
Loadline Calibration [Enabled]
設置AUTO [這個應該是防掉壓吧?我設開啟,SP2004無法順利跑,
所以設AUTO,可能電壓需要調整後,開啟才能順利跑SP2004]
CPU GTL Reference [0.63x]
設置AUTO
North Bridge GTL Reference [0.67x]
設置AUTO
DDR2 Channel A REF Voltage [Auto]
設置AUTO
DDR2 Channel B REF Voltage [Auto]
設置AUTO
DDR2 Controller REF Voltage [DDR2_REF]
設置AUTO [這項目我設DDR2_REF時,
DRMA電壓調2.2v,還是跑2.3v一樣多1v,所以設AUTO]
SB 1.5V Voltage [Auto]
設置一樣
NB LED Selection [NB Volt]
系統預設
SB LED Selection [SB Volt]
系統預設
CPU LED [CPU Volt]
系統預設
Voltiminder LED [Enabled]
系統預設
CPU Spread Spectrum [Auto]
設置Disabled
PCIE Spread Spectrum [Auto]
設置Disabled
CPU Configuration 頁面設定
CPU Ratio Control [Auto]
系統預設
C1E Support [Disabled]
設置Enabled,因為日常使用即為OC 3.6G,
沒滿載時讓BIOS降2個倍頻低溫跑2.7G
CPU TM function: [Enabled]
設置Enabled [不懂該項目,目前設置系統預設值Enabled]
Vanderpool Technology [Enabled]
設置Enabled [不懂該項目,目前設置系統預設值Enabled]
Execute Disable Bit [Enabled]
設置Enabled [不懂該項目,目前設置系統預設值Enabled]
Max CPUID Value Limit [Disabled]
設置Disabled [不懂該項目,目前設置系統預設值Disabled]
Intel(R) SpeedStep(tm) Tech. [Enabled]
設置Enabled [不懂該項目,目前設置系統預設值Enabled]
以上是我主機板BIOS的設置^^
另「不懂該項目,目前設置系統預設值 」的部份,希望狂大或其他高手能幫解答,先謝謝了^^
ASUS Maximus formula真的是一塊超正點的板子,雖然比一般中階板貴了約4000元,但超頻能力真的不錯,不光CPU超頻,連記憶體上高頻都變得很EZ ;tongue;
不過沒有狂大的教學,很難馴服ASUS Maximus formula這塊板子吧.....呵呵呵