- 已加入
- 9/18/03
- 訊息
- 14,397
- 互動分數
- 2
- 點數
- 0
這次的Super pi 32m不再像上次一樣糊裡糊塗了
終於把上次無心之過修正,定下完美計劃
照我的理想時脈更加進些許去跑
不過個人蠻確定的是至少我試過的R3E bios(beta or non beta)
完全無法讓980x 的測試版(Q3FE)去跑2:12(所以memory時脈當然會比較低)
在下希望Asus也能修正這個問題
**以下中英對照
This time I ran with 2:10 finally, and I am pretty sure that 2:12 is definitely no work for at least Q3fe.
So this is what my set up is:(測試設置)
test bed:
cpu: Q3fe
mobo: R3e bios 0047
memory : Avantium Leopard II
VGA: evga 240gt
psu: Antec Tpq-1200OC
HD: WD 320aaks
OS: win2003ent. TW sp1(I have to use this version because vga driver issue)
Thermolab pot (can pour more LN2 in)
Tweak & tools:
校調
1.OS
2003 tw R1 sp1, because I figured it out if you use original 2003 ent tw,
when you use the video card after NV 250gts later, driver won't be installed.
使用windows 2003 SP1 R1是因為我的顯卡,在NV 250gts之後發行的卡,
完全沒辦2y941windows 2003原始版上裝上支援的Driver
on the boot.ini,
I just add PAE for system for better recognize
I have 6gb memory:p
also I change the line: NoExcute=AlwaysOff
我在Boot.ini內加上 PAE是因為win2003本身有支援4gb以上memory,
但是要加PAE才會抓到6gb以上.
另外也把NoExcute=Optin改成 AlwaysOff
2.OCX spi tweaker:
I ran once normal waza , then start 32m for 2 loops, shut down 32m windows
and then start tweaker again for CDT in oder to get
"available real memory size over 550MB easily and save time processed too much for CDT IV"
在使用ocx spi tweaker時,為了增大available real memory size(大於550mb)
我使用一次正常的copywaza完後跑兩圈再關掉super pi 32m,
再跑一次自創的CDT理論的檔案搬移,所以整個有效的實際記憶體跑32m將近570mb
3.BIOS
suggestion:
建議
a. vcore
if you are planning to run high vcore ,
say over 1.85v(normally not really stable for me,
you have to do--->50% calibration. that's just my own experience on R3E.
在你計劃想跑32m之前,如果你要拼高頻(CPU)
cpu vcore當然要加大壓,我先前跑都不太敢試超過1.85
因為一方面es無保,燒死就是沒保固,
一方面, 1.85v以上不穩的話會發生在如果你在bios的防掉壓上選用
Full calibration 則是Vcore是強制衡定輸出
不管外面LOADING如何 會高於設定一點點
50%是依據INTEL規範, 把斜率調到不要那麼斜
b. vtt
R3E has been very good for low vtt on retail 980x,
but NOT ES,
or I should say if you want to run high uncore freq. on ES;
you need quite a high vtt for secure 2:10 and high uncore.
In this case I used almost 1.55v vtt
就我們所看到很多網兄測過R3e的VTT,是可以很低的
但是跑super pi,重的是uncore, memory都要高時脈
加上ES uncore真的不是那嚜好,
所以以我這狀況跑到4800+mhz,
又要memory 跑2100mhz+ 7-7-6-20-70以上
vtt至少要1.55以上才會穩(基本上是在維持uncore穩定在4800mhz以上
memory2100算還OK)
********************************************************
so here is the successful 32m run after I got about 4 times failed run.
以下就來看看..
這一個成功之前..至少失敗有4次..都是因為vtt太低..
in the middle of running(when I get camera ready, and focus done,
it already 12~13 loops done:p)
開跑到中途準備好相機,已經跑到13 loops
done..fast huh..
跑完..很快吧..
this all the info here:
所有的cpuz..和memory uncore等等 info
windows screen shot:
windows抓圖
跑完後有測了一下我的q3fe..沒縮缸也沒問題..阿彌陀佛...:D
終於把上次無心之過修正,定下完美計劃
照我的理想時脈更加進些許去跑
不過個人蠻確定的是至少我試過的R3E bios(beta or non beta)
完全無法讓980x 的測試版(Q3FE)去跑2:12(所以memory時脈當然會比較低)
在下希望Asus也能修正這個問題
**以下中英對照
This time I ran with 2:10 finally, and I am pretty sure that 2:12 is definitely no work for at least Q3fe.
So this is what my set up is:(測試設置)
test bed:
cpu: Q3fe
mobo: R3e bios 0047
memory : Avantium Leopard II
VGA: evga 240gt
psu: Antec Tpq-1200OC
HD: WD 320aaks
OS: win2003ent. TW sp1(I have to use this version because vga driver issue)
Thermolab pot (can pour more LN2 in)
Tweak & tools:
校調
1.OS
2003 tw R1 sp1, because I figured it out if you use original 2003 ent tw,
when you use the video card after NV 250gts later, driver won't be installed.
使用windows 2003 SP1 R1是因為我的顯卡,在NV 250gts之後發行的卡,
完全沒辦2y941windows 2003原始版上裝上支援的Driver
on the boot.ini,
I just add PAE for system for better recognize
I have 6gb memory:p
also I change the line: NoExcute=AlwaysOff
我在Boot.ini內加上 PAE是因為win2003本身有支援4gb以上memory,
但是要加PAE才會抓到6gb以上.
另外也把NoExcute=Optin改成 AlwaysOff
2.OCX spi tweaker:
I ran once normal waza , then start 32m for 2 loops, shut down 32m windows
and then start tweaker again for CDT in oder to get
"available real memory size over 550MB easily and save time processed too much for CDT IV"
在使用ocx spi tweaker時,為了增大available real memory size(大於550mb)
我使用一次正常的copywaza完後跑兩圈再關掉super pi 32m,
再跑一次自創的CDT理論的檔案搬移,所以整個有效的實際記憶體跑32m將近570mb
3.BIOS
suggestion:
建議
a. vcore
if you are planning to run high vcore ,
say over 1.85v(normally not really stable for me,
you have to do--->50% calibration. that's just my own experience on R3E.
在你計劃想跑32m之前,如果你要拼高頻(CPU)
cpu vcore當然要加大壓,我先前跑都不太敢試超過1.85
因為一方面es無保,燒死就是沒保固,
一方面, 1.85v以上不穩的話會發生在如果你在bios的防掉壓上選用
Full calibration 則是Vcore是強制衡定輸出
不管外面LOADING如何 會高於設定一點點
50%是依據INTEL規範, 把斜率調到不要那麼斜
b. vtt
R3E has been very good for low vtt on retail 980x,
but NOT ES,
or I should say if you want to run high uncore freq. on ES;
you need quite a high vtt for secure 2:10 and high uncore.
In this case I used almost 1.55v vtt
就我們所看到很多網兄測過R3e的VTT,是可以很低的
但是跑super pi,重的是uncore, memory都要高時脈
加上ES uncore真的不是那嚜好,
所以以我這狀況跑到4800+mhz,
又要memory 跑2100mhz+ 7-7-6-20-70以上
vtt至少要1.55以上才會穩(基本上是在維持uncore穩定在4800mhz以上
memory2100算還OK)
********************************************************
so here is the successful 32m run after I got about 4 times failed run.
以下就來看看..
這一個成功之前..至少失敗有4次..都是因為vtt太低..
in the middle of running(when I get camera ready, and focus done,
it already 12~13 loops done:p)
開跑到中途準備好相機,已經跑到13 loops
done..fast huh..
跑完..很快吧..
this all the info here:
所有的cpuz..和memory uncore等等 info
windows screen shot:
windows抓圖
跑完後有測了一下我的q3fe..沒縮缸也沒問題..阿彌陀佛...:D
