想問 超頻神人 我這樣的設定是對的嗎? [記憶體上1800問題一問]

[new_word_devil]

測試平台：

CPU：Core™ 2 Quad Q9550
RAM：金士頓 KHX1800C8D3K2/4G
RAM風扇：OCZ 第二代XTC記憶體風扇 [型號：OCZTXTCC2]
主機板：GA-EP45T-UD3R [Rev1.0] [BIOS：F6]
測試軟體：Memtest86+ V4.00

MB Intelligent Tweaker(M.I.T.) (頻率/電壓控制)  BIOS 首頁

Robust Graphics Booster [Auto] 為預設值
CPU Clock Ratio [8x] 手動變更
Fine CPU Clock Ratio [+0.0] 為預設值
CPU Frequency 3.59Ghz (449x8) 手動變更

CPU Host Clock Control [Enabled] 手動變更
CPU Host Frequency (Mhz) [449] 手動變更
PCI Express Frequency (Mhz) [Auto] 為預設值
C.I.A.2 [Disabled] 手動變更

Advanced Clok Control 進階選單項目

CPU Clock Drive [800mV] 為預設值
PCI Express Clock Drive [900mV] 為預設值
CPU Clock Skew [0ps] 為預設值
MCH Clock Skew [0ps] 為預設值

DRAM Performance Control

Performance Enhance [Standard] 手動變更
MCH Frequency Latch [Auto] 為預設值
System Memory Multiplier (SPD) [Auto] 為預設值
Memory Frequency (Mhz) [1796] 主板 Auto 自秀

DRAM Timing Selectable (SPD)

CAS Latency Time [8] 手動變更
tRCD [8] 手動變更
tRP [8] 手動變更
tRAS [24] 手動變更

Advanced Timing Control進階選單項目

tRRD [Auto] 為預設值
tWTR [Auto] 為預設值
tWR [Auto] 為預設值
tRFC [Auto] 為預設值
tRTP [Auto] 為預設值
Command Rate(CMD) [Auto] 為預設值

Channel A/B Timing Settings進階選單項目

Static tRead Value [Auto] 為預設值
tRD Phase0 Adjustment [Auto] 為預設值
tRD Phase1 Adjustment [Auto] 為預設值
tRD Phase2 Adjustment [Auto] 為預設值
tRD Phase3 Adjustment [Auto] 為預設值
Trd2rd(Different Rank) [Auto] 為預設值
Twr2wr(Different Rank) [Auto] 為預設值
Twr2rd(Different Rank) [Auto] 為預設值
Trd2wr(Same/Diff Rank) [Auto] 為預設值
DIMM1 Clock Skew Control [Auto] 為預設值
DIMM2 Clock Skew Control [Auto] 為預設值
DDR Write Leveling [Enabled] 手動變更
DDR Write Training [Enabled] 手動變更

Channel A/B Driving Settings進階選單項目

Driving Strength Profile [Auto] 為預設值
Data Driving Pull-Up Level [Auto] 為預設值
Cmd Driving Pull-Up Level [Auto] 為預設值
Ctrl Driving Pull-Up Level [Auto] 為預設值
Clk Driving Pull-Up Level [Auto] 為預設值
Data Driving Pull-Down Level [Auto] 為預設值
Cmd Driving Pull-Down Level [Auto] 為預設值
Ctrl Driving Pull-Down Level [Auto] 為預設值
Clk Driving Pull-Down Level [Auto] 為預設值

Mother Board Voltage Control

>>> CPU
Load-Line Calibration [Disabled] 為預設值
CPU Vcore [Auto] 為預設值
CPU Termination [Auto] 為預設值
CPU PLL [Auto] 為預設值
CPU Reference [Auto] 為預設值
>>> MCH/ICH
MCH Core [Auto] 為預設值
MCH Reference [Auto] 為預設值
MCH/DRAM Reference [Auto] 為預設值
ICH I/O [Auto] 為預設值
ICH Core [Auto] 為預設值
>>> DRAM
DRAM Voltage [1.740V] 手動變更
DRAM Termination [Auto] 為預設值
Ch-A Data VRef. [Auto] 為預設值
Ch-B Data VRef. [Auto] 為預設值
Ch-A Address VRef. [Auto] 為預設值
Ch-B Address VRef. [Auto] 為預設值

以上為基本記憶體上1800 的設定 其他細項 BIOS 就不列舉！有更改的有標紅色 有錯誤請回信告知 特別說明: (如下)

1.此對記憶體 已經換過3次 以正常不超頻 全設 [Auto] 測 1333 就會有錯誤訊息 快的話 約跑10分鐘左右就會出現！
2.DDR Write Leveling [Enabled] or DDR Write Training [Enabled] 若設 [Auto] 測 RAM 約 整個回圈 Pass 1 次 也會有錯誤！但打開後 可以跑到整個回圈 6次 然後才會出現錯誤 不知 打開 來說 是不是會有影響? <---這點比較重要！

多謝回答!!!! 感激不盡~~~~~